新型变径提升管冷模实验研究

›› 2018, Vol. 49 ›› Issue (3): 48-53.

新型变径提升管冷模实验研究

刘丙超,苏鲁书,张善鹤,祝晓琳,李春义

中国石油大学（华东）重质油国家重点实验室

收稿日期:2017-09-06 修回日期:2017-11-14 出版日期:2018-03-12 发布日期:2018-03-20
通讯作者: 李春义 E-mail:chyli@upc.edu.cn

COLD MOLD STUDY OF A NOVEL DIAMETER-CHANGING RISER REACTOR

Received:2017-09-06 Revised:2017-11-14 Online:2018-03-12 Published:2018-03-20

摘要/Abstract

摘要： 以催化裂化平衡剂和常温空气为介质，在新型变径提升管冷模实验装置上考察了不同的操作条件对固体循环量及颗粒浓度轴径向分布的影响，并描述了扩径段内的流动结构。结果表明：固体循环量随着表观气速的增大而增大，随着伴床料位高度的增加而增大，且在改变进气比例时，循环量随着预提升气占比的增加而增大；与传统提升管相比，该新型结构提升管内部存在多种流型且扩径段内固含率有明显增加，底部扩径段内为密相湍流形态，固含率为0.3~0.4，上部等径段为稀相气力输送形态，固含率无明显变化，为0.05~0.1。新型变径提升管对斜管下来的催化剂起到了重新分配的作用，抑制了传统的“环-核”流动，使颗粒浓度径向分布更加均匀。

关键词: 新型变径提升管, 流动结构, 固体循环量, 固含率

Abstract: The effects of different operating conditions on the solid circulation and solid holdup distribution in the axial and radial directions of a novel diameter-changing riser were investigated in a cold-mold test using FCC equilibrium catalyst and room temperature air medium. The flow structure within the diameter expanded segment was described. Experimental results showed that the amount of solid circulation increases with the increase of the superficial gas velocity, and the bed height. When changing the ratio of intake air, the amount of circulation increases with the increase of the proportion of pre-lifting gas. Compared with the traditional riser, there are many kinds of flow patterns in the new structure riser, and the solid holdup in the expanded section is significantly increased. A dense phase turbulent flow pattern exists in the bottom region (εs is about 0.3—0.4) and a dilute phase pneumatic conveying form is observed in the upper region (εs is about 0.05—0.1) where the solid holdup has no obvious change. The novel variable diameter riser is able to redistribute the solid particles coming from the inclined pipe, resulting in inhibition of the traditional “ring-core” flow pattern, and making the radial distribution of solid holdup more uniform.

Key words: novel variable diameter riser, flow structure, solid circulation, solid content

刘丙超苏鲁书张善鹤祝晓琳李春义. 新型变径提升管冷模实验研究[J]. , 2018, 49(3): 48-53.

参考文献

[1] Zhu H, Zhu J. Comparative study of flow structures in a circulating-turbulent fluidized bed[J]. Chemical Engineering Science, 2008, 63(11):2920-2927.
[2] 吴文龙, 韩超一, 李春义,等. 变径提升管反应器扩径段内气固流动特性研究[J]. 石油炼制与化工, 2014, 45(11):54-59.
[3] 钟孝湘, 侯拴弟, 郑茂军,等. 抗滑落提升管反应器流体力学性能的研究[J]. 石油炼制与化工, 2000, 31(7):45-50.
[4] 刘翠云, 冯伟, 张玉清,等. FCC提升管反应器新型预提升结构开发[J]. 炼油技术与工程, 2007, 37(9):24-27.
[5] 张欢. 多产低碳烯烃变径提升管数值模拟研究[D]. 中国石油大学, 2008.
[6] Zhu X, Geng Q, Wang G, et al. Hydrodynamics and catalytic reaction inside a novel multi-regime riser[J]. Chemical Engineering Journal, 2014, 246(246):150-159.
[7] Issangya A S, Grace J R, Bai D, et al. Further measurements of flow dynamics in a high-density circulating fluidized bed riser[J]. Powder Technology, 2000, 111(1–2):104-113.
[8] Zhu H, Zhu J. Gas-solids flow structures in a novel circulating-turbulent fluidized bed[J]. Aiche Journal, 2008, 54(5):1213–1223.
[9] Wang X, Gao S, Xu Y, et al. Gas–solids flow patterns in a novel dual-loop FCC riser[J]. Powder Technology, 2005, 152(1–3):90-99.
[10] Gan J, Yang C, Li C, et al. Gas–solid flow patterns in a novel multi-regime riser[J]. Chemical Engineering Journal, 2011, 178(24):297-305.
[11] Zhu X, Li C, Yang C, et al. Gas–solids flow structure and prediction of solids concentration distribution inside a novel multi-regime riser[J]. Chemical Engineering Journal, 2013, 232(9):290-301.
[12] 祝晓琳, 李春义, 杨朝合,等. 变径提升管反应器扩径段内固含率分布研究[J]. 石化技术与应用, 2013, 31(3):181-184.
[13] 宫海峰, 杨朝合, 徐令宝,等. 多层进气变径提升管内颗粒固含率分布研究[J]. 当代化工, 2011, 40(1):41-44.
[14] Geng Q, Zhu X, Liu Y, et al. Gas–solid flow behavior and contact efficiency in a circulating-turbulent fluidized bed[J]. Powder Technology, 2013, 245(8):134-145.
[15] 韩超一, 陈晓成, 吴文龙,等. 内构件对变径提升管内气固流动特性的影响[J]. 石油炼制与化工, 2016, 47(1):5-10.